Vag tacho usb 3.01 driver for mac
![Vag tacho usb 3.01 driver for mac Vag tacho usb 3.01 driver for mac](http://pinreel.weebly.com/uploads/1/2/6/6/126653826/361868007_orig.jpg)
However, I'm not sure that's the solution. I'm not in the possition to get the original values into the eeprom. I have observed that there is a difference in the eeprom contant after reprogramming:Ġ000 : 01 40 03 04 99 D0 00 00 A0 2D 08 00 00 00 98 0A. Have the same problem with my vgatacho 3.01 from china.Īfter running Licznik vagtacho is not more running anymore. This chip seems to be the wiped/corrupted by the latest version of vag-tacho, and is real cause of the earlier sw no longer recognising the cable.Īfter reading around various forums it seems the Atmega chip cannot be programmed via usb, it needs to be desoldered from the pcb and reprogramed with a dedicated reader? I am hoping this is not the case but it looks like it is :( The firmware ept file needs to match the chip in your cable however otherwise it will not work.įrom my research it appears that with the later cables there is a 2nd Atmega chip as mentioned above. Once you have this you can read & write the cable firmware.
![Vag tacho usb 3.01 driver for mac Vag tacho usb 3.01 driver for mac](https://is4-ssl.mzstatic.com/image/thumb/Purple118/v4/d4/4d/2f/d44d2f8c-5df2-1324-d7f3-c6a286381a0f/source/643x0w.jpg)
Sory mi enghlis if you not anderstend mail me and i help you step by step need to use mprog:
VAG TACHO USB 3.01 DRIVER FOR MAC UPDATE
edit this file ftd2xx.inf and this FTD2XXUN.INI you see pid and vid ex in file original VID_0403&PID_D099 if you red yours cabel in my comp/properties/hardware/device manager/usb ftidi usb iso interface /properties/details you see VID_0403&PID_6001 or not import VID_xxxx&PID_xxxx modifi wuiz new pid and vid all you see in //ftd2xx.inf and this FTD2XXUN.INI // update driver wuiz this modifi and use mprog too write good dumpĭo not use software wuiz new driver created ok use after yuo write dump and instal original driver from vag tacho So If you have a documentation or a friend of yours about the UN4 (UKNSI) speedometer give me pls a short reply, or a PN or an email to your cabel is not recognising you fix. In my opinion everyting is impossible until someone does it, so I could get it somehow on someway, but I don.t wanna pay 180 €uros to a guy that need 5 minutes for it, neither pay Audi for that. How can i obtain it, what should I buy, cable or device, I guess I can find every electronic device at, and what software do I need. So iavnxxx if I am gettin it right I do need another cable for that or what ?my big problem is the UN4 or UK-NSI Speedometer. How do I read the EEPROM, or the login from it ? WHAT DO I NEED ? NP I'll buy it
![Vag tacho usb 3.01 driver for mac Vag tacho usb 3.01 driver for mac](https://ae01.alicdn.com/kf/HTB1UvcFHpXXXXbUXFXXq6xXFXXXB/220066677/HTB1UvcFHpXXXXbUXFXXq6xXFXXXB.jpg)
That's all I need the login for the damn UN4 dash. I forgot to mention that the UN4(UKNSI) one was on the CAR by Audi, so I bought the car with it, but I put the VDO in it cause now I have a Voltmeter and Oil Temp., but I am missing the DAMN login for the UN4 Speedometer, and I don't have even the plastic piece from the service key cause on it I would had have the LOGIN code.